XLERATOR® HAND DRYER - ZINC DIE-CAST COVER


	You have 0 item(s) in your cart

Total: $0.00
View Cart - Checkout

Janitorial & Industrial

Office

Furniture

Food Service

Sheds & Outdoor

Call Us Toll-Free at: 1-877-894-4884

Janitorial/Industrial

Rubbermaid

Paper Products

Air Fresheners

Washroom Accessories

Industrial Marking Pens

Sky-Scapes®

Touchless Restroom

Cleaning Chemicals

Hand Dryers

	Bobrick
	World Dryer
	American Specialties
	Bradley
	Excel Hand Dryers
	Sky Systems Hand Dryers

Floor & Carpet Care

Floor Buffing Pads, Sponges & Abrasives

Matting & Utility Cleaning Tools

Mopping Equipment

Odor Control

Soap & Skin Care

Brooms, Brushes & Accessories

Can Liners

Facility Maintenance Products

Floor Maintenance Equipment

Personal Care & Safety Supplies

Storage & Material Handling

Waste Receptacles

Wipers

Gloves

Training Videos

Closeout

Washroom Partitions & Hardware

Technical Concepts

Partition Replacement Hardware

Trash Can HeadQuarters

View Products By:
Name / Manufacturer / Category

Janitorial & Industrial

Hand Dryers

Excel Hand Dryers

Xlerator Hand Dryers

< Back to category

XLERATOR® Hand Dryer - Zinc Die-Cast Cover - Chrome Plated
EHD XL-C by Excel Dryer

• Zinc Die-Cast Cover - Chrome Plated
• Automatic Sensor
• Surface Mounted

FEATURES
• Dries Hands Completely in 10 to 15 Seconds
• Uses 80% Less Energy
• 95% Cost Savings vs. Paper Towels
• GREENSPEC® Approved and Helps Qualify for LEED® credits.
• Source Reduction Alternative
• Promotes Hygiene
XLERATOR Hand Dryers Help Qualify For LEED Credits.
XLERATOR Is First Hand Dryer To Be GreenSpec Approved!

SPECIFICATIONS

Dimensions:

11 3/4" LG. X 12 11/16" HIGH X 6 11/16" DEEP
(298 MM LG. X 322 MM HIGH X 170 MM DEEP)
Weight:16 LBS. (7.3 KGS.)

Construction

1. Hand dryer cover shall be a one-piece, heavy-duty, rib-reinforced, die-cast zinc alloy. It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically applied epoxy paint and fastened to a wall plate by two chrome plated tamper-proof bolts.

2. Hand dryer wall plate shall be equipped with (3) 7/8" (22 mm) diameter holes, one of which shall be suitable for use with surface conduit, for ease of wiring.

3. All internal hand dryer parts shall be coated according to Underwriters' Laboratories, Inc. requirements.

4. Entire mechanism shall be internally grounded.

Mechanism

1. Hand dryer motor shall be a series commutated through-flow discharge vacuum motor/blower (5/8 HP / 20,000 RPM) which provides air velocity of 16,000 LFM (linear feet per minute) at the air outlet and 14,000 LFM at the hands (4 inches [102 mm] below air outlet).

2. Hand dryer heating element (900 W) is constructed of Nichrome wire and mounted inside the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of up to 135°F (57°C) at a 72°F (22°C) ambient room temperature at the hands (4 inches [102 mm] below air outlet).

3. Hand dryer Control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are under the air outlet. There is a 35-second lockout feature if hands are not removed.

Limited Warranty

The hand dryer shall be guaranteed to be free from defects for a period of five (5) years. Warranty shall include factory performed labor as well as the repair or exchange of defective parts, at manufacturer's option.